illuminated switches miniature audio/video pushbuttons kp series general speci?cations: kp how to order: 1 2 3 4 sales@greatecs.com www.greatecs.com 1 KP0115ACAKG03CF-1SJB 5 01 02 15a c n s a b k travel & force: stroke: 4.5mm (.177??) actuation force: 1.9n stroke: 3.5mm (.138??) actuation force: 1.6n pole & circuits: spst off-(on) normally open contacts actuation: tactile nontactile tactile/audible (just for 02 type) plungers: 9.2mm plunger for 12.0mm cap 11.6mm plunger for 15.0mm and 17.4mm caps housing: black only g03 cf rgb 1 2 3 contacts & terminals: gold contacts and straight pc terminals; 100ma @ 12v dc leds: red/green bicolor red/green/blue caps sizes: 12.0mm square 15.0mm square 17.4mm square 1 2 3 6 7 illuminated switches 6 7 8 4 5 8 9 10 f s t cap types: flat sculpured home key 9 jb caps colors: clear lens & white diffuser 10 electrical capacity (resistive load) low level: 100ma maximum @ 12v dc other ratings contact resistance: 200 milliohms maximum insulation resistance: 100 megohms minimum @ 250v dc dielectric strength: 1,000v ac minimum between contacts for 1 minute minimum 1,500v ac minimum between contacts & case for 1 minute minimum mechanical life: 5,000,000 operations minimum; 1,000,000 operations minimum for custom rectangular switch/cap assembly (at center of cap) electrical life: 5,000,000 operations minimum nominal operating force: kp01: 1.9n maximum for tactile & nontactile models (at center of cap) kp02: 1.6n maximum for tactile, nontactile & tactile/audible models (at center of cap) travel: kp01: pretravel .122? (3.1mm); overtravel .055? (1.4mm); total travel .177? (4.5mm) kp02: pretravel .091? (2.3mm); overtravel .047? (1.2mm); total travel .138? (3.5mm) materials & finishes plunger/upper housing: polyacetal lower housing: movable contact: stainless steel with gold plating stationary contacts: gold over copper alloy switch terminals: brass with tin plating environmental data operating temp range: ?25c through +50c (?13f through +122f) humidity: 90-95% humidity for 240 hours @ 40c (104f) vibration: 10 ~ 55hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & retur ning in 1 minute; 3 right angled directions for 2 hours shock: 51g (500m/s 2 ) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) installation cap installation force : 50.0n maximum do wnw ard force on act ua tor pcb p rocessi ng sol dering : clea ni ng : these d evices are not process sea led . hand c lean locall y us ing al cohol based s olut ion. stan dards & cer ti catio ns ul r ecognitio n these sw it ches are d esign ed for u se in a lo w-vo ltage, lo w-curr en t, l ogic-level circui t. wh en u se d a s intend ed in a logic-level circuit, th e r esu lts do not produce hazardous e ne rg y. 12.0mm square cap (12.0) sq .472 (0.9) dia typ .035 (0.6) dia typ .024 (1.3) dia typ .051 (7.62) .300 (4.5) .177 (12.7) .500 (2.54) typ .100 (12.7) .500 l2l1 1 1a c (6.5) .256 (3.6) .142 (0.3) .012 (4.5) .177 (12.7) .500 (0.45) dia .018 (11.5) .453 (1.1) .043 (6.0) .236 (23.0) .906 (5.0) .197 (6.4) .252 (7.62) .300 (0.6) typ .024 (2.54) typ .100 (12.7) .500 (15.0) sq .591 1 1a l1 l2 com 15.0mm square cap (0.9) dia typ .035 (0.6) dia typ .024 (1.3) dia typ .051 (7.62) .300 (4.5) .177 (12.7) .500 (2.54) typ .100 (12.7) .500 l2l1 1 1a c (15.0) sq .591 (7.62) .300 (0.6) typ .024 (2.54) typ .100 (12.7) .500 (15.0) sq .591 1 1a l1 l2 com (7.0) .276 (3.6) .142 (0.3) .012 (4.5) .177 (0.45) dia .018 (12.7) .500 (11.5) .453 (4.5) .177 (23.0) .906 (6.0) .236 (1.1) .043 (6.4) .252 kp0115anbkg03cf-2sjb 17.4mm square cap (17.4) sq .685 (0.9) dia typ .035 (0.6) dia typ .024 (1.3) dia typ .051 (7.62) .300 (4.5) .177 (12.7) .500 (2.54) typ .100 (12.7) .500 l2l1 1 1a c (11.5) .453 (1.1) .043 (6.0) .236 (23.0) .906 (4.5) .177 (7.0) .276 (3.6) .142 (0.3) .012 (4.5) .177 (12.7) .500 (0.45) dia .018 (6.4) .252 (7.62) .300 (0.6) typ .024 (2.54) typ .100 (12.7) .500 (15.0) sq .591 1 1a l1 l2 com kp0115anbkg03cf-3sjb wave soldering: see pro le a in supplement section. manual soldering: see pro le a in supplement section. glass ber reinforced pbt or csa certi cation: the kp series pushbuttons have not been tested for ul recognition or csa certi cation.
illuminated switches miniature audio/video pushbuttons kp series sales@greatecs.com www.greatecs.com 2 kp0115acakg03rgb-1sjb cutaway illuminated switches plunger position ( ) = momentary connected terminals throw & switch schematic pole model normal down normal down note: switch terminals 1 & 1a are actually marked on the switch. sp kp0115a kp0215a off (on) normally open 1-1a spst pole & circuit 1 (com ) 1a pole & circuit kp0115anbkg03rgb-2sjb kp0115anbkg03rgb-3sjb 12.0mm square cap with rgb led 17.4mm square caps with rgb led terminal detail (12.7) .500 dia .500 (12.7 (4.5) .028 typ typ .035 (0.7) dia (0.9) dia .177 1 .300 1a (7.62) .051 (1.3) typ .150 (3.81) typ .060 (1.52) g(-) r(-) b(-)(+) (12.0) sq .472 .500 (5.0) .197 .256 (6.5) (1.1) .043 (4.0) (23.0) .906 .157 (11.5) .453 typ .008 (0.2) sq .150 (3.81) (6.4) .252 .142 (3.6) (12.7 (0.3) .012 (4.5) .177 sq .591 (15.0) (12.7) .500 1 1a .060 (1.52) typ (7.62) .300 typ (0.6) .024 see terminal detail (15.0) sq .591 (17.4) sq .685 (3.81) (4.5) .177 (1.1) (7.0) .276 .043 (4.0) (23.0) .906 .157 (11.5) .453 typ sq (0.2) .008 .150 (6.4) .252 .142 (3.6) (12.7 .500 .012 (0.3) g(-) r(-) b(-) common anode (+) 1a 1 sq (15.0) .591 (12.7) .500 typ (1.52) .060 (7.62) .300 1a 1 (4.5) .177 typ .024 (0.6) see terminal detail (12.7) .500 dia .500 (12.7 (4.5) .028 typ typ .035 (0.7) dia (0.9) dia .177 1 .300 1a (7.62) .051 (1.3) typ .150 (3.81) typ .060 (1.52) g(-) r(-) b(-)(+) terminal detail g(-) r(-) b(-) common anode (+) 1a 1 g(-) r(-) b(-) common anode (+ ) 1a 1 terminal detail (12.7) .500 dia .500 (12.7 (4.5) .028 typ typ .035 (0.7) dia (0.9) dia .177 1 .300 1a (7.62) .051 (1.3) typ .150 (3.81) typ .060 (1.52) g(-) r(-) b(-)(+) sq (15.0) .591 (12.7) .500 typ (1.52) .060 (7.62) .300 1a 1 (4.5) .177 typ .024 (0.6) see terminal detail (3.81) (4.5) .177 (1.1) (7.0) .276 .043 (4.0) (23.0) .906 .157 (11.5) .453 typ sq (0.2) .008 .150 (6.4) .252 .142 (3.6) (12.7 .500 .012 (0.3) 15mm square caps with rgb led plungers a 9.2mm plunger for 12.0mm cap 9.2mm plunger is designed with a narrower neck to hold the 12.0mm cap. (9.2) .362 (6.4) .252 11.6mm plunger for 15.0mm & 17.4mm caps b 11.6mm plunger is designed with a wider neck to hold both the 15.0mm and 17.4mm caps. (11.6) .457 (6.4) .252
illuminated switches miniature audio/video pushbuttons kp series sales@greatecs.com www.greatecs.com 3 illuminated switches bicolor led specifications determined at a basic temperature of 25c. leds are an integral part of the switch and are not available separately. led circuit is isolated and requires an external power source. if the source voltage exceeds the rated voltage, a ballast resistor is required. the resistor value can be calculated by using the formula in the supplement section. note: for applications that require white illumination, contact factory. red green blue unit forward peak current i fm 30 30 30 ma continuous forward current i f 20 15 15 ma forward voltage v f 2.0 3.3 3.4 v power peak dissipation p d 40 80 80 mw reverse peak voltage v rm 555v dominant wavelength d 625 525 470 nm current reduction rate above 25c if 0.50 0.50 0.50 ma/c ambient temperat ure range C25 ~ +50 c red green blue common anode (+) rgb attention electrostatic sensitive devices color custom rgb led specifications amber can be achieved by simultaneous illumination of red & green. attention electrostatic sensitive devices red green unit minimum luminous intensity i v 30 50 mcd standard luminous intensity i v 60 115 mcd forward peak current i fm 30 (25 for amber) 25 (22 for amber) ma continuous forward current i f 20 20 ma forward voltage v f 2.1 3.5 v power peak dissipation p d 75 100 mw reverse peak voltage v rm 44v wavelength at peak emission 619 ~ 630 520 ~ 535 nm current reduction rate above 25c i f 0.38 0.32 ma/c ambient temperature range C25 ~ +50 c cf colors (+) com red green (C) l 2 (C) l1 leds are an integral part of the switch and are not avail - able separately. led circuit is isolated and requires an external power source. if the source voltage exceeds the rated voltage, a ballast resistor is required. the resistor value can be calculated by using the formula in the supplement section. athe electrical specications shown are determined at a basic temperature of 25c
illuminated switches miniature audio/video pushbuttons kp series sales@greatecs.com www.greatecs.com 4 illuminated switches cap types & colors 1 used on a plunger at3083 flat cap f s at3086 home key cap t at3084 flat cap f at3079 sculptured cap s at3087 home key cap t 12.0mm square at3078 sculptured cap at3085 flat cap at3080 sculptured cap s at3088 home key cap t clear lens white diuser jb lens & diuser colors available: clear/white optional protective guard at4170 available; contact factory. 2 15.0mm square f 3 17.4mm square used on b plunger used on b plunger (6.5) .256 (12.0) sq .472 (6.5) .256 (12.0) sq .472 (7.0 ) .276 (15.0) sq .591 (7.0 ) .276 (15.0) sq .591 (7.0 ) .276 (17.4) sq .685 (7.0 ) .276 (17.4) sq .685 (6.5) .256 (12.0) sq .472 (2.6) dia .102 (7.0 ) .276 (15.0) sq .591 (2.6) dia .102 (7.0 ) .276 (17.4) sq .685 (2.6) dia .102 materials & finishes: lens - palycarbonate with glossy nish; diuser - polycarbonate with textured nish
illuminated switches miniature audio/video pushbuttons kp series sales@greatecs.com www.greatecs.com 5 illuminated switches custom rectangular cap assembly switch/rectangular cap assembly led holder determined at a basic temperature of 25c. center led is an integral part of the switch. leds are not sold separately. led circuits are isolated and require an external power source. if the source voltage exceeds the rated voltage, a ballast resistor is required. the resistor value can be calculated by us- ing the formula in the supplement section. red unit forward peak current i fm 30 ma continuous forward current i f 20 ma forward voltage v f 2.0 v reverse peak voltage v rm 4v dominant wavelength d 623 nm current reduction rate above 25c i f 0.32 ma/c ambient temperature range C25 ~ +50 c color led switch/rectangular cap assembly has 3 leds to achieve bright and even illumination. one led (in center of switch bottom) is an integral part of the switch; the other 2 leds and 2 led holders are packaged separately. assembly & installation instructions (12.7) .500 (3.1) .122 dia (2.54) .100 cathode (4.8) .189 (5.9) .232 (10.4) .409 (6.7) .264 (+) (-) kp0115acbkg03cjb for tactile kp0115anbkg03cjb for nontactile install led into led holder (quantity 2). solder leds and led holders into pcb. solder switch into pcb making sure that the two outer leds and led holders clear the bot - tom side opening of the cap. 1 2 3 (17.4) .685 (34.8) 1.370 pcb led holder led switch .500 (12.7) (4.5) .177 1 .300 (7.62) 1a (22.86) .900 (2.54) .100 (2.54) .100 .500 (12.7) (1.3) dia typ .051 (0.8) dia typ .031 (0.9) dia typ .035 lC l+ footprint typ .018 (0.45) sq (0.6) .024 sq (15.0) .591 (12.7) .500 1a (4.5) .177 1 (7.62) .300 (0.3) .012 l+ lC .500 .276 (7.0) (23.0) .906 (6.0) .236 .100 (2.54) (12.7 (3.6) .142 see below for complete assembly of switch, leds and led holders. contact factory for other led colors. led specifications cap assembly dimensions the electrical specications shown are
illuminated switches miniature audio/video pushbuttons kp series sales@greatecs.com www.greatecs.com 6 illuminated switches assembly instructions for square caps as shown in the accompanying illus- tration, the cap and plunger are designed with tabs and notches to assure proper orientation of the cap on the switch. holding the switch tightly, pull the cap o the switch. once the cap as - sembly is released from the plunger, the lens and diuser can be separated. pry up the lens inserted at the step on the diuser. attention electrostatic sensitive devices after aligning notches with tabs, join the lens and diuser. hold the switch tightly without touching the terminals. firmly press the cap onto the plunger by applying pressure from one side to the other until both are snapped together. removal of cap assembly installation or cap orientation & separation of lens & diuser replacement of cap notch tab step plunger notches cap assembly plunger switch legends lens film insert diffuser st op (10.5) dia .413 (8.97)dia .353 (0.76) typ .030 (13.0) dia .512 (11.48) dia .452 (0.76) typ .030 (15.3) dia .602 (0.76) typ .030 (13.77) dia .542 (9.8) sq .386 (8.28)dia .326 (0.76) typ .030 (0.5) r .020 (12.8) sq .504 (11.28) dia .444 (0.76) typ .030 (0.5) r .020 sculptured cap lens sculptured or home key cap film inserts flat cap lens flat cap film inserts (9.8) sq .386 (8.28) sq .326 (0.76) typ .030 (0.5) r .020 (12.8) sq .504 (11.28) sq .444 (0.76) typ .030 (0.5) r .020 (13.4) sq .528 (11.88) dia .468 (0.76) typ .030 (0.5) r .020 (12.0) sq .472 (9.8) sq .386 (15.0) sq .591 (12.8) sq .504 (17.4) sq .685 (13.4) sq .528 printing on diuser is not advisable. custom rectangular cap lens custom rectangular film insert (13.77) .542 (0.91)typ .036 (15.6) .614 (33.0) 1.299 (28.75) 1.132 (0.5) r .020 (2.125)typ .084 film insert material and thickness: clear polyester; 4 mil (100) maximum thickness (13.4) sq .528 (11.88) dia .468 (0.76) typ .030 (0.5) r .020 (13.77) .542 (0.76) typ .030 (15.3) .602 (30.28) 1.192 (28.75) 1.132 recommended methods: laser etch, screen print, or pad print on lens; epoxy based ink is recommended. shaded areas are suggested printable areas for lens & film inser t. general information and basic specications are presented bere for customers who want to do their own legends.
|
